Specifikace CertiFiber® Max
Technické údaje
Produkt podporuje měření útlumu, výkonu i délky pro single-mode vlákna s přesností ±0,10 dB (výkon) a délkou až do 25 km s nepřesností ±1 m + 1 %
| Multi-Fiber Optical Power Meter (per module) | |
| Specifications apply at 23°C, unless otherwise noted. | |
| Parameter | Single-mode |
| Included UniPort Adapter | Non-contact MPO 12-fiber pinned |
| Optional Uniport Adapters | MPO 12/16/24 and MMC 16/24 pinned or unpinned |
| Detector Type | 16 large core fibers coupled to 16 InGaAs photodiodes. |
| Supported Fiber Type | Single-mode 9/125 µm |
| Calibrated Wavelengths | 1310 nm, 1550 nm |
| Power Measurement Linearity1 | ±0.10 dB |
| Power Measurement Repeatability1,2 | ±0.02 dB |
| Power Measurement Reproducibility1,3 | ±0.1 dB |
| Power Measurement Uniformity 4 | ± 0.1dB |
| Loss Measurement Budget5 | 10 dB |
| Re-calibration Period | 1 year |
|
1. For the measurement range -10 dBm to -20 dBm. All photodiodes, over the measurement range. After a 5-minute warmup. 2. Maximum variation of power measurements when the measurement is repeated multiple times (i.e. 5 times) without disturbing the optical connector during 5 seconds at -12-dBm SM. 3. Maximum variation of power measurements when the measurement is repeated multiple times (i.e. 5 times) when the optical connector is disconnected and reconnected between repeated measurements at - 12-dBm SM. 4. Maximum variation between any one detector when compared to any of the other detectors, including the optical power meter duplex port at -20dBm SM. 5. Loss measurement budget specification provides flexibility within the power measurement range, for example, -10 dBm to -20 dBm for single-mode. |
|
| Multi-Fiber Optical Sources (per module) | |
| Specifications apply at 23°C, unless otherwise noted. | |
| Output port | MPO 16 pinned |
| Fiber Type | 9/125 µm |
| Central Wavelengths (nm) |
1310 ± 20 1550 ± 20 |
| Emitter Type | Fabry-Perot laser |
| Spectral Width (nm)1 | ≤5 (1310 nm and 1550 nm) |
| Output Power (dBm) Nominal | ≥ -12 dBm |
| Power Stability (dB) 2 | ± 0.10 |
| Launch Condition3 | Not applicable |
| Length Measurement Range 4 | up to 25 km |
| Length Measurement Uncertainty | +/- 1 meter + 1% of length |
| 1.
1. RMS for Fabry Perot lasers; FWHM for LEDs (typical). 2. At constant temperature, relative to power level after 15-minute warm up, compliant for 8 hours. 3. At 850 nm. Measured at the output of an encircled flux maintaining patch cord connected to the module’s output port. 4. Length measurement is round trip time delay the cable under test. |
|
| Multi-Fiber Visual Fault Indicator (Source Port) | |
| Connector | MPO 16, pinned (when testing, this port will be connected to a Test Reference Cord which is available in MPO 12/16/24 and MMC 16/24 pinned and unpinned). |
| Total Output Power | >-5 dBm <0 dBm, continuous wave, at the 9/125 µm patch cord for single-mode source |
| Operating Wavelength | 635 nm nominal |
| Output Modes | Continuous, pulsed blink frequency (2 Hz to 3 Hz) |
| Laser Safety | Class II CDRH |
| Optical Power Meter - Duplex Port (per module) | |
| Specifications apply at 23°C, unless otherwise noted. | |
| Parameter | Single-mode |
| Input Connector | Cylindrical ferrule duplex connectors (only one ferrule is measured at a time) |
| Default Port Adapter | LC Duplex |
| Optional Port Adapters | SC Duplex |
| Detector Type | 1 mm InGaAs photodiode accommodates one fiber at a time |
| Supported Fiber Type | Single-mode 9/125 µm |
| Calibrated Wavelengths | 1310 nm, 1550 nm |
| Power Measurement Range | +5 dBm to -45 dBm |
| Power Measurement Uncertainty1 | < ± 0.35 dB |
| Power Measurement Linearity1,2 | ±0.10 dB |
| Power Measurement Repeatability3 | ±0.02 dB |
| Power Measurement Reproducibility4 | ±0.05 dB |
| Optical Connector Interface | Accepts simplex LC or SC non-angled (UPC) and (APC) end face |
| Re-calibration Period | 1 year |
|
1. Under the following conditions: a. For calibrated wavelengths. Power level 10 µW (-20 dBm), continuous wave (CW) for absolute power. b. Divergent beam, NA = 0.20 for 50/125 µm and NA = 0.14 for 9/125 µm c. Ambient temperature 23° ± 3 °C d. FC/UPC connector with ceramic ferrule e. After a 15-minute warm-up f. Traceable to SI g. Based on calibration and metrology requirements. 2.For the measurement range -5 dBm to -40 dBm. 3. Maximum variation of power measurements when the measurement is repeated multiple times (i.e. 5 times) without disturbing the optical connector during 5 seconds at -30dBm MM and -12dBm SM. 4.Maximum variation of power measurements when the measurement is repeated multiple times (i.e. 5 times) when the optical connector is disconnected and reconnected between repeated measurements at -30dBm MM and -12dBm SM. |
|
| Environmental Specifications (tested with module installed into Versiv mainframe) | |
| Operating Temperature | -10°C to +45°C |
| Storage Temperature | -10°C to +60°C |
| Operating Relative Humidity |
0 % to 95 % noncondensing, 0°C to 35°C 0 % to 70 %, 35°C to 45°C |
| Vibration | Random, 2 g, 5 Hz to 500 Hz |
| Shock | 1-meter drop test |
| Safety | IEC 61010-1 |
| Pollution Degree | 2 |
| Altitude |
Operating: 4 km Storage: 12 km |
| EMC | IEC 61326-1 |